移印噴漆面金屬油墨銷售廠家!

本產品主要用于各種金屬、玻璃、真空電鍍、水電鍍、電泳、陽極氧化鋁、電解板、鋁塑板、噴塑、噴粉、靜電噴漆面、烤漆面以及各種天花吊頂氧化板、鏡面板、覆膜板、輥涂板等制品的絲印及移印。

油墨特性：

1、平光、附著力佳、耐汽油、耐化學品；

2、手感好，流平性佳、面光潔；

3、表面硬度好，耐沖擊性能強、抗刮傷；

4、耐汽油、耐酒精、耐化學品程度佳；

印刷：

選用網目為100-350目，以120T網紗計算涂覆蓋面積每公斤達30~35㎡。

表干時間自然揮發5-15分鐘，實干時間在24小時以內，48小時后達較佳性能。

1．用配套專用稀釋劑開油水

2．用718洗網水洗網。

3．或添加配套硬化劑10%可增加附著力,提高墨膜硬度。

4．烤箱80℃烘烤10分鐘佳能更優。

測試方法（完全干燥后）：

1．3M膠紙粘在畫有百格的油墨表面45度角迅速拉起不脫油。

使用方法：

1．建議用我公司專用稀釋劑進行稀釋，不建議使用783慢干稀釋劑稀釋，使用前應充分?jǐn)嚢瑁煤箅S時密封。

2．?dāng)嚢钑r(shí)加本公司配套開油水10-12%，稀釋到印刷適合粘度，移印稀釋使用移印專用稀釋劑；用718洗網水清洗。

3．不得與其它類型油墨混合使用，否則容易出現其他附著力，化學反應等不良現象。

4. 加入固化劑的油墨使用時限為8小時，過期請棄用，剩余油墨不可回收

注意事項：

1．各種承印物料的外觀相似，但可能會是不同的材料，客戶需先試印，確其符合要求后，再批量生產。

2．在移印過程中，如出現拉絲或散開，可適當加入一些慢干膏即可;

3．環境溫度過高，將會影響油墨原有質量。白色超越150都會變色，烘烤時請用木質材料墊底進行烘烤，不得直接接觸鐵

4．根據氣候變化，請遠離火源，陰暗處15度-30度環境下存放

Brand: but MY name: anodic oxidation INK Numbers: 65496

Anodic oxidation ink series

The product is produced with advanced import acrylic resin and senior pigment after fine grinding system, used in combination to ABS, PP, PET, all kinds of metal, glass, ceramic, stone, electroplating (water cut electroplating), anodic alumina surface and roast (spray paint products of screen and pad printing, not needing curing agent, and does not need to bake, can obtain excellent adhesion.

Ink characteristics:

1 the classification includs glass, adhesion, good resistance to gasoline, alcohol, resistance to chemicals;

2, feel is good, flow ping sex, good surface is bright and clean;

3 and fine surface hardness, impact resistance properties of strong, resistance to scratch;

4, resistant to gasoline, alcohol, resistant to chemicals resistant degree good;

Printing:

Choose for 100-350 mesh mesh to 120 T nets yarn with coverage area calculation per kilogram of 30 to 35 ㎡.

Dry time table natural volatilize 5 to 15 minutes, action in time within 24 hours, after 48 hours of optimum performance.

1. With matching special thinner, open oil and water

2. Wash washing nets with 718 net.

3. Or add hardener 10% supporting can increase adhesion, improve ink film hardness.

4. Preheat the oven to 80 ℃ bake for 10 minutes Canon even better.

Test method (dry) :

1.3 M tape stuck in the picture has's ink surface 45 degree Angle quickly pull up not to take off oil.

2. The purity of 99% alcohol 500 G force in ink surface wipe 300 times back and forth without decoloring.

Method of use:

1. The proposal with my company special thinner to dilute, not recommended dry thinners diluted 783 slow, before the use should be fully mixing, use at any time after sealing.

2. Add the company supporting stirring open 10 to 12%, oil and water dilute the printing for viscosity, pad printing dilution use moving printing special thinner,; Use clean water to wash the nets 718.

3. Not with other kinds of printing ink mixed use, otherwise easy to have other adhesion, chemical reactions and other bad phenomenon.

4. Add hardener inks use time limit for 8 hours, please not used, the remaining expired ink not recycling

Note:

1. All kinds of printing material appearance similar, but may be of different material, customers are required to meet the requirements of the ShiYin, indeed, its, then batch production.

2. In moving printing process, such as a wire drawing or away, can be appropriately to add some slow dry paste can;

3. Environmental temperature is too high, will influence the quality of the original ink. White will change color, roasted beyond 150 when please use woodiness material bottom, and may not directly contact roast iron

4. According to climate change, please away from fire, the shadows 15 degrees-30 degrees environment for